As an Amazon Associate I earn from qualifying purchases. Without Any Extra Cost to You!
A septic system is an underground treatment facility for wastewater management in a home. This septic system treatment plant is installed in any home or development without access to a public sewer.
You can also build a septic tank system yourself to save money by hiring a professional septic designer and excavator.
If you are a beginner, the work will be difficult for you; however, if you work serially and understand what you need to consider, the work will be simple. This article will explain how to construct your septic system.
So, let’s start with the question: What should be considered before installing a septic system?
A tiny house typically has a smaller lot and less space to work with when installing a septic tank. It is preferable to select a lightweight tank that is easier to transport and install on your property.
When considering a tiny house, the location of your tank installation is critical. Heavy rain can also impact these tanks, so keep them as far away from the house as possible.
On the other hand, you should think about installing a vent pipe. Because of the tiny house’s limited space, it’s critical to install the vent pipe in a location that doesn’t take up much space. As a result, it is preferable to hire a professional vent pipe installation designer.
Now, my friend, we are just getting started.
5 Easy Steps To Installation The Septic System
If you are moving into a new tiny house, you will be responsible for installing a septic system. We always recommend that any septic tank installation be performed by a suitably trained and qualified professional. However, if you believe you can complete this task, follow the steps and proceed accordingly.
1. Design the septic system
It is always necessary to have a basic design to work from when starting any project. This means that when you arrive at the job site, you will have a clear plan of action.
Because it is a tiny house, you must design it carefully because the vent pipe and tank must be installed in a small space. On the other hand, find out where you want to go inside the building about where you want to put the septic tank, so design it accordingly.
During your project’s site survey and design stages, you should have checked the depth of your incoming pipework and ordered a tank with the appropriate invert levels.
Don’t forget to test the soil because it determines the soil’s ability to absorb wastewater and predicts the required size for the leach field by measuring its water absorption rate.
2. Excavate the hole for the tank and vent pipe according to the design
Make sure it’s big enough for the tank, then put in the proper type of base for it to sit on. Calculate the distance between the top of the inlet and the bottom of the tank.
If you intend to install a gravity feed system, shut down the system completely, open the bleed at the highest radiator, and use a vacuum cleaner to create suction from the lowest point, excavating the soil for pipe by the rule.
3. Place the vent pipe and tank
It is preferable to locate your tank close to where it will be needed; for example, if it will be used for bathroom purposes, place it closer to where your bathroom is located.
Then, using the recommended lifting system, carefully lower the tank into the hole while checking that the inlet and outlet orientations are correct and the tank is level.
If you are unsure about upgrading your septic tank or installing a new system yourself, you should hire a professional.
4. Make sure the ventilation
As the tank fills up with waste, it generates foul-smelling gases known as septic gases. The sewage odours and gases easily find their way out and away from your home due to the low pressure in the pipe itself.
The vent allows septic gases to exit the system, preventing them from accumulating and causing an explosion. When a toilet is flushed, or a sink is drained, vent pipes supply fresh air to each plumbing fixture in the house, assisting the system in moving water through the drainage pipes.
5. Make sure the septic system work properly
When a septic system fails, the drain field is usually not working correctly. When a septic tank overflows, the effluent can enter the drain field and clog the pipes. This causes clogs in the house’s sinks and toilets.
Water and sewage from toilets drain and sinks can occasionally back up into the home. Bathtubs, showers, and sinks drain at a slower rate. The plumbing system is gurgling. If you find all type of these sign, then contact with professional, and they will solve it.
Your sewage system is a critical component of your home. A maintenance contract with the supplier of your sewage treatment plant or septic tank is always recommended.
FAQs:
Question: How do tiny houses handle sewage?
Answer: The RV low-flush toilet with a holding tank is the most common sewage system for tiny homes because it uses little water but produces blackwater that must be emptied.
Answer: Composting toilets are most likely the most popular type of alternative toilet system for tiny houses. They use the natural decomposition process to break down waste and turn it into usable compost.
Question: What size septic tank do I need for a tiny house?
Answer: In general, regulations require a 1000-gallon capacity for a household septic tank. Like a tiny house, you can have a septic tank with a capacity of 750 – 900 gallons.
Question: Is human poop good fertiliser?
Answer: The use of unprocessed human faeces as fertiliser is dangerous because it may contain pathogens that cause disease. It is possible to reduce human excreta into compost safely.
Final Word
A septic system is an underground treatment facility for wastewater management in a home. As a result, it must be perfectly installed so that all processes run smoothly. In this article, we’ll go over 5 DIY steps for installing a remote house septic system.
But as a beginner, all the planning and working according to planning may not be perfect. So our advice is to hire a professional installer.
Leave a Reply